-
- Type: Ball valve (quarter-turn shut-off valve)
- Load: Handles internal fluid pressure; not designed for mechanical load-bearing
- Cage: Not applicable (solid ball with seats instead of cage structure)
- Performance: Fast operation, low pressure drop, reliable sealing, long cycle life
- Construction: Valve body + perforated ball + seats (PTFE or similar) + stem + handle/actuator
- Use cases: Fluid shut-off in pipelines, hydraulic and pneumatic systems, water and oil control, industrial processing
- Note: Best for on or off control; not ideal for precise flow regulation as partial opening can cause seat wear
₨ 999.00
-
- Type: Rotodynamic pump (centrifugal type)
- Load: Primarily hydraulic load from fluid movement; radial and axial forces on impeller
- Cage: Not applicable (no rolling element cage; uses impeller and shaft system)
- Performance: Steady flow, moderate to high efficiency, best for low-viscosity fluids
- Construction: Casing, impeller, shaft, seals, bearings, and drive motor
- Use cases: Water transfer, irrigation, HVAC systems, industrial fluid movement, cooling circuits
- Note: Requires proper priming before operation; avoid dry running and ensure correct sizing for best efficiency
₨ 19,999.00
-
- Type: Check valve (non-return valve)
- Load: Handles fluid pressure loads in one direction; blocks reverse pressure
- Cage: Internal guide or spring mechanism (varies by design such as spring-loaded or swing type)
- Performance: Quick response, low backflow leakage, stable operation under varying pressures
- Construction: Valve body, seat, disc/ball or poppet, optional spring mechanism, threaded or flanged ends
- Use cases: Pumps, compressors, pipelines, hydraulic and pneumatic systems, water and fluid control setups
- Note: Install in correct flow direction (marked on body); ensure compatibility with pressure, fluid type, and operating conditions
₨ 999.00
-
- Type: Gate valve (rising stem or non-rising stem)
- Load: Handles fluid pressure loads; not designed for mechanical side loads
- Cage: Not applicable (no cage, uses gate/disc mechanism)
- Performance: Low pressure drop when fully open; reliable sealing when closed; slower operation compared to other valves
- Construction: Valve body + gate (disc) + stem + सीट (seat) + bonnet; typically cast or forged metal construction
- Use cases: Pipeline isolation, water systems, oil and gas flow control, industrial shut-off applications
- Note: Avoid using for throttling as partial opening can cause wear and vibration; operate in fully open or closed position for best performance
₨ 999.00
-
- Type: Reciprocating piston pump (positive displacement)
- Load: Handles high-pressure loads with steady flow output
- Cage: Not typically cage-based; uses piston, seals, and valve assemblies
- Performance: High efficiency, accurate flow control, capable of very high pressures
- Construction: Cylinder block, reciprocating piston, inlet/outlet valves, seals, and drive mechanism
- Use cases: Hydraulic power units, chemical injection, pressure cleaning, oil transfer, industrial fluid systems
- Note: Requires regular seal maintenance and clean fluid supply; not ideal for highly abrasive or contaminated fluids without proper filtration
₨ 34,000.00
-
- Type: Submersible pump (water/sewage/deep well types)
- Load: Handles hydraulic load based on fluid head and flow demand
- Cage: Not applicable (sealed motor and impeller assembly)
- Performance: High efficiency, consistent flow, self-priming due to submerged operation
- Construction: Sealed motor housing, impeller, shaft, mechanical seals, and waterproof cable
- Use cases: Borewells, drainage pits, sewage systems, irrigation, construction sites
- Note: Must remain submerged during operation for cooling; running dry can damage the pump
₨ 35,000.00
-
- Type: Water and particulate separator (air line filter unit)
- Load: Handles flow pressure and contaminant load within rated capacity
- Cage: Not applicable (uses internal filter element instead of bearing cage)
- Performance: High moisture separation efficiency, consistent filtration, low pressure drop
- Construction: Housing (metal or polymer bowl), filter element, baffle or centrifugal mechanism, drain valve
- Use cases: Air compressors, pneumatic systems, spray booths, industrial air lines, fluid filtration setups
- Note: Install in correct flow direction and maintain regularly by draining collected water and replacing filter elements when needed
₨ 500.00
